Sunday, September 2, 2012

Gift Card Holder - times three


A couple of days ago, I posted a few photos of a gift card holder I made using the Cricut Artiste cartridge.  There are several gift card holders on this cartridge - the one I chose is on page 55 (letter G, card function, on the overlay).


I cut three of the holders at 5 inches, using the Gypsy so I could eliminate the tick marks for the scorelines.  The cardholder is designed so both sides of the paper will be seen.  I chose some pretty floral paper with a pink swirl on the reverse side from K & Company.



After the holders were cut, I simply scored and folded them in the middle and then scored along the base of the card and folded the sides up.


This is how the holder looks after scoring and folding.  I always eliminate the tick marks to make my folded edges neater.

 

The smaller inner section is sized to hold a plastic gift card with a little notch to make it easier to grasp the card.


To assemble the card holder, you just need to add strong adhesive to the sides and base of the center section.  I used Scor-Tape as you can see in the photo above.


I made three identical card holders for three gift cards.  To present the cards, I decided to make a "large" card.  I took a sheet of 12 x 12 dark green Bazzill textured cardstock and folded it in half for a 6 x 12 inch card.


I attached each of the card holders to the card base, using Scor-Tape again.  I like this adhesive because it is strong and does not leave a mess.  You do have to be careful to place your item correctly the first time because it is a very aggressive adhesive and it is difficult or impossible to move a piece that you have stuck done crooked or in the wrong spot.


The cards were a birthday gift so I wanted to add a birthday sentiment.  I used the banner cut from page 35 (number 5 on the keypad, accent 1 function).  This shape has a coordinating stamp that comes with the  Artiste bundle .  I cut the banners from the same paper with the pink side up and stamped the "
Happy Birthday" with Fired Brick Distress Ink.


I did not adhere the banners to chipboard but I did pop them up a bit with some foam dots.


Here is the inside of the card with three sets of birthdays wishes.  I signed on the left side of the card with  white ink.


The cards are placed in the holders with the bottom sides showing since they are fixed in a vertical position.  This hides the value of the card so there is a moment of anticipation as it is pulled out.


I wanted the front of the card to look like a package so I simply used another piece of the floral cardstock cut at 5 1/2 x 11 1/2 inches for the layer.  I wrapped some ruffled pink ribbon around the daisy paper and taped it on the back.  Then I added a layer of burgundy satin ribbon in the center of the pink ribbon.


Once the ribbons were centered and fixed in place, I added a piece of burgundy ribbon for a bow.


This is the top of the "package" or the front of the card.  This was a quick and simple to make the gift card presentation a little more special.

If you are thinking about purchasing the Artiste cartridge, it is available only through Close to my Heart consultants.  My friend Melanie Brown is a consultant and she would be happy to help you.  Melanie's site is HERE.   The Cricut Artiste Cartridge bundle is HERE on her site - it includes three coordinating stamp sets and three sheets of chipboard shapes. 

When you purchase the bundle, you will qualify to purchase  the September Stamp of the Month, Fall Favorites for just $5.   Until September 30th, you can also get the special National Stamping Month set for only $5 - it is a double set you can see HERE and you add it to your cart HERE.

I hope you are having a great weekend - we'll be enjoying another family birthday party today as the triplets are turning 9!  I have to finish up their cards this morning and I also hope to move a few more things around in my craftroom - if I can manage without help from my husband who shouldn't be using his injured hand.

Subscribe to Capadia Designs if you would like to have new posts delivered directly to your email. Share/Bookmark

1 comment:

  1. Diane thanks for showing me how to make the gift card holder on the Artiste Cartridge. It came in very hand for a Wedding card and gift I needed to make. Question for you. How do you figure out what size to cut some of these items on the Artise cartridge is is trial and error or do you measure it on your gypsy? Still love your blog even though you don't do as much Cricut stuff!

    ReplyDelete

Thanks for taking the time to leave a comment. I love to hear from the people who read my blog. I moderate all comments to keep spam off the blog without making you decode the squiggly letters so your comment may not appear immediately.